| Customization: | Available |
|---|---|
| Usage: | Emergency Light |
| Emergency Time: | 3-4h |
|
Still deciding? Get samples of US$ 20/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Product Specification:
| Type | LEK010-200NC | |
| For Luminaires with external led driver 3~200W | ||
| Input Voltage | AC220~240V~ | |
| Frequency | 50/60Hz | |
| Output (Emergency Brightness Efficiency) | 3W 100% | |
| 6W 90% | ||
| 10W 60% | ||
| 20W 30% | ||
| 30W 24% | ||
| 40W 15% | ||
| 50W 12% | ||
| 60W 10% | ||
| 80W 7% | ||
| 100W 6% | ||
| 150W 4% | ||
| 200W 3% | ||
| Battery (4 options) | Ni-Cd 7.2V 1500mAh | |
| Ni-Cd 7.2V 2000mAh | ||
| Ni-Cd 7.2V 3000mAh | ||
| Ni-Cd 7.2V 4000mAh | ||
| Discharge time | Ni-Cd 7.2V 1500mAh | 60 minutes |
| Ni-Cd 7.2V 2000mAh | 90 minutes | |
| Ni-Cd 7.2V 3000mAh | 120 minutes | |
| Ni-Cd 7.2V 4000mAh | 180 minutes | |
| Charge time | 24Hrs | |
| Operating Temp | -10~50°C | |
| IP Rating | IP20 | |
| Materials of the Inverter case | Metal | |
| Case size | 182*42*28mm | |
| Work mode | non-maintainance | |
| Protection | Over-charge/over-discharge | |
| Led Indicator | Red-AC power | |
| Test button | Yes | |
• Battery: in normal occasion, please change battery when discharging time is less than 100 minutes after being charged for 24 hours or battery leakage When changing battery, Cut of the main power, take apart the lamp, removing the battery plug and replace the old one with a new battery of same specification ,then the driver will be OK. Usually the lifespan of battery can be more than 3years.
Note: The positive and negative of battery should not be connected reverse, and we should avoid directly short-circuit the battery. Explosion will be caused if using unmatched battery. Please abide by local rules when discarding old battery.
• Light source: 3-50W LED lamps with external driver, please change to the same light source if light source is broken or brightness is not enough.
Warning: As the inner PCB includes 220V/50HZ high voltage, so it must be unloaded/opened ONLY by professional technical.
Labelling
Maintenance
1. It should be connected according to the wiring diagram on the emergency kit's surface strictly
2. When connecting to AC power, see if it works normally, at this time, green indicating light is on. At the same time, red indicating light would be on too, but it will be off after full charged. Two status of LED lamp:
• The LED lamp is off when its own driver is not connected 220V AC power;
• The LED lamp if on when its own driver is connected 220V AC power
3. Press the test button, the emergency kit enters the status of simulation of power failure. At this time, the indicating light of main power (green) and charging (red) is off, while the emergency indicating light (blue) is on, it is in emergency status, and the LED lamp is working, but the brightness is not so high. After loosing the button, it will return to main power status again.
4. Cut off the emergency kit input switch, the LED lamp will be in emergency status.
5. Cutting off the LED lamp's connection to the emergency kit in emergency status, the emergency kit will stop supplying power to the LED lamp, the emergency indicating light would be off.
* Finishing installation after ensuring all are normal after testing.
* After testing the above steps, if OK, installation is finished.
6. Keeping a record of maintenance and maintaining the emergency kit and LED lamp regularly
7. Checking regularly to ensure its lifespan and usage.
Notes
• Usually it should be installed at stairs, corridor and the ceiling, except outside environment.
• The main power supply of this emergency kit should be controlled by the light's switch, NOT influenced by the other switches.
• Please note that its working voltage is 85V-265V AC power 47-63Hz. It would be broken if connected with 380V high voltage
• If the indicator lights can't work as usual, the main power should be cut off immediately and maintain the emergency kit
• Checking if there are any broken emergency kits before use, and please do not use any broken ones or out-of- shaped ones.
• If the emergency kit is not used for over 3 months, it should be connected to AC power for full charging and discharging (until LED lamp is completely off). Then keeping the emergency kit on main power for 24 hours and put it in dry ventilated place.
• this should be operated by professional technical for your safety.
){kind=link}